Mega-catch Mini Manual do Utilizador Página 1

PELLET STOVEMiniPLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS CO

10HORIZONTAL EXHAUST THROUGH WALL INSTALLATION:Vent installation: install vent at clearances specified by the vent manufacturer.A chimney connector sh

11InstallationExhaust Tube3" (75mm) or 4" (100mm) "PL" or "L" ventWall Thimble45° Elbow with screen orTermination CapHig

                    

To accomplish a outside vertical pipe installation, follow steps 1 through 5 in the “INSIDE VERTICAL INSTALLATIONS - FREESTANDING” section and

14InstallationRain capStorm collarSeal plate (cover plate)Existing masonry flueVent pipe (single wallstainless flex pipe orsolid PL vent)Fireplace dam

InstallationEXTERIOR MOUNTED EXHAUST BLOWER (20-070):The Mini can be equipped with an externally mounted exhaust blower. This optional

InstallationTYPICAL THROUGH WALL WITH EXTERIOR BLOWER KIT INSTALLATION - HORIZONTAL TERMINATION:Electrical Cable90° Elbow45°Elbow with Rodentscreen or

17Roof SheathingRain CapRoof FlashingRoof RaftersCeiling JoistsVent PipeExterior WallSheathingOutside VentTerminationInstallationTYPICAL THROUGH WALL

InstallationTHERMOSTAT INSTALLATION:If the unit has been placed in the HI / LOW mode, the unit will be taken to a low or idle setting when the thermos

19out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly, decreasing the air in the fire

2Introduction...3Ratin

InstallationOPTIONAL PANEL KIT:This kit must be installed before the unit is started. 20Figure 30: Screws at back of the cab side.Figure 28: Screws ab

21Installation123Figure 31: Installing Hopper Lid.Installing Hopper Lid:1. Attach the hopper brackets to the back of the unit with a screw in e

TroubleshootingDO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly.

23TroubleshootingüPoor Quality Fuel – Insufficient energy in the fuel to produce enough heat to keep the stove burning or operational.üExhaust Tempera

Troubleshooting7. The convection blower will not function normally.üClean all grill openings at the back and below unit .üPress the fan button; does t

25Wiring DiagramConnectThermostatHereRedRedRedRedBrownBrownBrownBrownWhiteWhiteWhiteWhiteWhite115VWhite220VBlueWhiteWhiteOrangeOrangeOrangeOrangeYello

Parts ListReference Number Description Part Number 1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001 2 Auger Motor - 115V EF-0013 High Limit Temp S

27Parts ListReference Number Description Part Number 17 Firebox Panel Set with Insulation 50-116218 Side Louver 50-116319 Burn Pot 50-116620 Burn Pot

Parts Diagram - ComponentsMini - ComponentsApril 200528

29Parts Diagram - SteelMini - Steel ComponentsApril 2005

3Introduction* This manual is designed for the technician in conjunction with the owner’s manual. *RATING LABEL LOCATION:The rating label is located o

WarrantySherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrica

31NAME OF OWNER:_________________________________________ADDRESS:_____________________________________________________________________________________

4IntroductionELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical c

5InstallationDECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:1. Remove the right and left hand cabinet sides by loosening the three (3) T-20 T

6InstallationAPPLIANCE DIMENSIONS AND SPECIFICATIONS:Figure 2: Dimensions of Mini. 151/2"(393 mm)187/8"(481 mm)171/2"(444 mm)195/8"

7InstallationCLEARANCES TO COMBUSTIBLES:ALCOVE CLEARANCES:This unit may be installed in an alcove. Maintain these clearances to combustibles.Minimum A

fumes such as stairwells, covered breezeway, etc.2. Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shieldi

9EXHAUST AND INTAKE LOCATIONS:101/16"(255mm)61/8"(156mm)21/16"(53mm)Figure 8: Mini Inlet and Outlet Location. EXHAUSTBase of unit to ce